King Kutter Lawn Mower 999996 Manual de usuario

PO Box 1200 305 Commerce Drive Winfield, Alabama 35594 XB FREE FLOATING FINISHING MOWER Part No 999996 www.kingkutter.com

BEFORE PUTTING FINISHING MOWER INTO SERVICE (IMPORTANT-INSTRUCTIONS PRIOR TO START UP) SHIPPED WITH OIL IN GEARBOX SHIPPED WITHOUT GREASE IN GREASE F

SAFETY TRAINING  Safety is a primary concern in the design and manufacture of our product. Un-fortunately, our efforts to provide safe equipment

PREPARTION  Never operate the tractor and mower until you have read and completely under-stand this manual, the Tractor Operator’s Manua

OPERATIONAL SAFETY  The use of this equipment is subject to certain hazards that cannot be pro-tected against by the mechanical means o

OPERATIONAL SAFETY continued...  Never allow the cutting blade to contact such items. Cut material higher at first, allowing finishing mow

OPERATIONAL SAFETY continued...  Pass finishing mower diagonally through sharp dips and avoid sharp drops to prevent “hanging up” tractor and finis

16 ATTACHING TO TRACTOR WARNING Never stand between tractor and finishing mower while backing up

17 ATTACHING TO TRACTOR continued... STEP 5 Place and hold inner PTO shaft section next to outer section and check if PTO shaft is too lon

18 SIZING PTO SHAFT STEP 1 Cutting the PTO shaft to length. NOTE: Be sure to cut equal lengths of each PTO shaft section. Cla

19 OPERATING INSTRUCTIONS This mower was designed to CUT LAWN GRASS ONLY. Use of your finish- ing mower to cut any material other than lawn g

20 FINISHING MOWER OPERATION STEP 1 Before each use perform the maintenance described in maintenance section (pg# 21) STEP2 Read, understand, and

21 MAINTENANCE 1). Periodically check and maintain proper gear oil level. 2). Every 8 hours, grease spindles (3), roller axle (1), wheel forks (4)

22 TO REPLACE BELT: STEP 1 Remove PTO shaft. STEP 2 Remove top cover. STEP 3 Loosen nut on adjustment pulley to allow for movement.

23 Figure D Figure E

26 MAINTENANCE SAFETY  Good maintenance is your responsibility. Poor maintenance is an invitation to trou-ble.  Follow good shop practices.

27 SAFETY SIGN LOCATIONS The types of safety signs and locations on the equipment are shown in the illustra-tion below. Good safety requires that yo

28 1

29 2 3

30 4 5

31 6 7 8

TO THE PURCHASER This manual contains valuable information about your new King Kutter Mower. It has been carefully prepared to give

32 9 10

33 11 12 MODEL NO. DESCRIPTION SN# XXXXXXXXXX

32 XB FINISHING MOWER

33 Ref. No. Part Name Part Number 5-1/2’ 1 Top Cover 124684 2 Gearbox Plate 403029 3 Spindle Unit -Spindle 502303 4 Idler Pulley -Single 1640

34 22" PTO 147022 Ref. No. Part Name 147022 1 Roll Pin Kit 500131 2 Male Tube End Yoke 151045 3 Implement End Yoke 151040 4 Female Tube

35 Blade Spindle Unit Ref. No. Part Name 502303 1 & 2 Bearing Kit - (2) Ball Bearings (6205), (2) Seals (TCM25x52x7TC), (4) Snap Rings 555009

36 40 HP GEARBOX

37 Ref. No. Part Name Gearbox 184000 1 Snap Ring 106138 2 Input Seal (NAK 35 x 54 x 10) 156010 3 Front Cap 129015 4 Front Cap Gasket 124130 5

38 BONDIOLI- (BYPY) 1). There are 3 white tabs around the cover as shown in (A in FIG. 1). Take a screwdriver and press against the tabs one at

39 BONDIOLI COVER REMOVAL FIGURE- 1 FIGURE– 2 FIGURE– 3 FIGURE– 4 FIGURE– 5 EUROCARDAN SERIES 4 COVER REMOVAL LA MAGDALENA COVER REMOVAL

It is the purchaser and/or operator’s responsibility to….  Read and understand the information contained in this manual.  Operate, lubricate,

40 PTO SHAFTS COVER REMOVAL EUROCARDAN SERIES 5 1). There are 2 black tabs around the cover as shown in (B in FIG. 1). Take a flat screwdriver and

41 1. Limited Warranty. King Kutter, Inc. (“King Kutter”), P.O. Box 1200, Winfield, Alabama 35594, warrants to the original retail purchaser

42 FIVE YEAR LIMITED GEARBOX WARRANTY King Kutter warrants to the original purchaser of any new King Kutter product equipped with a Gearbox, a Gearbox

43 King Kutter reserves the right to ask and inspect all parts prior to a warranty decision being made. Inciden-tal expenses such as lubricants and tr

5 CONTENTS ITEM PAGE Safety ... 6 Assembly Instructions ...

SAFETY READ AND FOLLOW THE INSTRUC-TIONS IN THIS MANUAL AND ESPE-CIALLY IN THE SAFETY SECTION. FAILURE TO DO SO CAN RESULT IN SERIOUS IN

EQUIPMENT SAFETY GUIDELINES  Safety of the operator and by standards is one of the main concerns in designing and de-veloping a mower. However, e

FINISHING MOWER ASSEMBLY INSTRUCTIONS STEP 1 With finishing mower still in crate, lay flat on a level surface. Remove the top & side sectio

9 Figure B Figure A Figure C